3D Printing with Monoprice Maker Select V2 – Episode 5 | DiiCooler Explained, Installed, and Tested!

3D Printing with Monoprice Maker Select V2 – Episode 5 | DiiCooler Explained, Installed, and Tested!

monoprice maker select v2 complete

Intro

In this episode, we are going to look at another important mod that will help improve the quality of our prints. This time around we are going to focus on improving the cooling situation of the V2 by replacing the stock cooling fan and shroud with the Dii Cooler aftermarket fan kit and accompanying shroud that we will print.

Buy Now - Affiliate Link

Part 5 Objectives

  • Understand why this mod is important
  • Explore it's benefits
  • Print the components
  • Install the new setup
  • Used our benchmark to see improvements
hour
Assembly
Difficulty
%
A little complex

Watch the overview video or keep reading the full article below.

A personalized Google Ad




The logic for the Mod

One reason I chose to go with this mod was that many of you peeps suggested it, so I’d like to say thank you all for that and two, the last benchy we printed had a few imperfections that I believe can be improved with better cooling. In particular, the top of the front window and the ceiling of the wheelhouse were a little messy as you can see here. This is due to the printer trying to bridge the gap and the filament not cooling fast enough to make it all the way across in one pass. So you are left with this drooping edge for several passes until it builds up enough cover the gap.

Mod Benefits

Here’s why that happened, the stock cooling setup is composed of a 40mm open intake style fan that blows it’s air into a shroud toward the nozzle from one direction. As you can see only a fraction of the air actually will get in contact with the nozzle.

This new setup will replace the stock fan and shroud with a larger 50mm blower style fan that will push the air into a cleverly designed shroud that than focuses the air directly onto the nozzle from 360 degrees.

Having 360 degrees of cooling means that no matter which way the filament is flowing it will get a consistent amount of cooling air. This is especially important for PLA filament that needs to be cooled the second it gets extruded.

Dii Cooler Mod Kit

Unlike with the brace mod from episode 3, this time I opted for a pre-assembled kit from the ultimate 3d printing store .com. The kit includes 1 m4x20mm screw, 2 m3x12mm screws, 1 m4 locknut, 2 m3 locknuts, and of course the 50x15mm brushless blower style fan. When I bought the kit it was $12.95. In this case, I don’t believe it would have been much cheaper to source the pieces individually, especially for the right sized and mounted blower style fan, although I did find a similar one on Amazon for around $8. Again though I’d go with the full kit if you can get it for the same price I did. Link to the fan and hardware kit in the description.

The only thing the kit doesn’t include is the new shroud which we will print ourselves. The option to have this printed professionally is available on thingy verse, for a cost if you want the best results the first time, but what’s the fun in that? You can find the files on Thingiverse at the link in the description.

It’s a good idea to use ABS filament instead of PLA to print the shroud because once installed it may warp or simply melt from the heat of the nozzle during normal printing. Of course, ABS has a host of other benefits that we will discuss in another video. I’ll be using Matchbox brand ABS filament to create this shroud.

DiiCooler Hardware Kit Thingy Verse DiiCooler Mod Link

first diicooler shourdFirst Shroud and Installation

Here we have the first finished shroud. Obviously not perfect, a bit of stringing on the inside and across the screw hole mounts but still the model as a whole is complete. Now to mount it and start seeing just how good or not this preforms.

Installing this mod is straightforward, all though I did have to make a small modification to make it work for me.

1. Start by making sure the printer is off and unplugged
2. Disconnect the stock fan’s power cable and unwrap the wire
3. Remove the top mounting screws for the stock fan shroud
4. On the new shroud position the m4 locknut in its mounting point and go ahead and attach the blower fan. It’s easier to do this now as the locknut will be hard to access later. Swing the fan out of the way for now.
5. Here is where I ran into a little trouble trying to mount the shroud. The smaller locknuts would not stay in place enough to tighten down the bolts. I decided to hold the bolts it in place upside down with an Allen key and tighten the nut down from the top using my racket. It may not look as nice as the other way around but it works for me.
6. Next, swing the fan into position. There are grooves on the inside of the shroud that will hold the fan in place, friction will do it if nothing else.
7. Plugin the new power connector, red to red and black to black, then wrap the cable so it stays out of the way of the fan.
8. Plug in the printer, turn it on, go to the fan speed settings and make sure the fan starts up. If not you may have to flip the connector around.

Now with everything up and running, I decided to print another shroud to see the impact of the new cooling solution. While there wasn’t a huge difference I did notice that the stringing that occurred on the roof of the first shroud wasn’t as bad on this print, so a definite improvement over the stock cooler already. I went ahead and installed the newer shroud to take advantage of the better quality.

installing shroud

One drawback to this mod is that the shroud is bulky and blocks you from seeing all but a small fraction of the nozzle. So leveling the bed and cleaning the nozzle is going to be a bit tricky without removing the shroud completely.

shroud and nozzle visability

New Benchy and Results

Now it’s time to add another benchy to our fleet and see what improvements we get from the improved cooling.

And well, it has to be said, this is the best quality benchy I’ve printed so far, of course still not perfect but the overall print quality has definitely improved over previous iterations, this is most evident in two key areas. The first is this little hole on the back, in both previous prints the round shape is not clearly defined and distorted but now it’s nicely defined and sharp. The other area is one I mentioned at the beginning of the episode. The top of the front window is almost perfectly smooth, no stringing or drooping at all, a stark contrast to the previous benchys.

before shroud benchy
after shroud benchy

The Conclusion

These two aspects of the model and the overall improved quality demonstrate how important it is to have a proper cooling setup for any printer, so weather you choose the Dii cooler or another aftermarket solution you’ll defiantly see improvements over the stock solution.

Buy Now - Affiliate Link

Leave a Comment





Other Posts

3D printing with cura and sketchup
3D Printing with Monoprice Maker Select V2 – Part 2 | SketchUp + Cura = Awesome
part 4-5 blog post
3D Printing with Monoprice Maker Select V2 – Episode 4.5 | Mounting a Camera
3d printing monoprice maker select v2
3D Printing with Monoprice Maker Select V2 – Part 1 | Overview and Assembly
part 7 post image
How Much Space Do You Need for a Monoprice Maker Select V2?